View UPD16434_5262.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
MOS INTEGRATED CIRCUIT
PD16434
1/8, 1/16 DUTY LCD CONTROLLER/DRIVER
DESCRIPTION
PD16434 is LCD controller/driver containing the interfacing features for a dot-matrix mode 8-, 16-time division
LCD and a microprocessor. PD16434 contains a 5- by 7-dot matrix character generator corresponding to ASCII/JIS. Therefore, user original patterns can be easily displayed.
FEATURES
* DOT matrix LCD controller/driver * 8- or 16-time division drive possible with a single chip 8-time-division : 400 (50 by 8) dots 16-time-division : 672 (42 by 16) dots * 8- or 16-time division drive possible with no chip 8-time-division : n x 400 (50 by 8) dots 16-time-division : n x 800 (50 by 16) dots * Display data storage RAM : 20 x 50 x 8 bits * Programmer specified dot (graphic) display * Capable of alphanumeric and symbolic displays thorough built-in ROM (5 by 7 dots) 160 characters * Parallel data input/output (Switch able between 4 and 8 bits) * Cursor manipulation command * Upgraded version of PD7228, PD7228A, PD7229, PD7229A
ORDERING INFORMATION
Part Number Package 80-PIN PLASTIC QFP (14 x 20) 80-PIN PLASTIC QFP (14 x 20), Standard ROM code 80-PIN PLASTIC QFP (14 x 20)
Note Note
PD16434G-xxx-12 PD16434G-001-12
5 5
PD16434GF-xxx-3B9 PD16434GF-001-3B9
80-PIN PLASTIC QFP (14 x 20), Standard ROM code
Note This package is only available in European market.
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for availability and additional information.
Document No. S10299EJ4V0DS00 (4th edition) Date Published April 2000 NS CP(K) Printed in Japan
The mark 5 shows major revised points.
1994, 1999
PD16434
PIN CONFIGURATION (Top View)
PD16434G-xxx-12
5 80-PIN PLASTIC QFP (14 x 20)
PD16434GF-xxx-3B9 80-PIN PLASTIC QFP (14 x 20)
C38 C39 C40 C41 C42/R15 C43/R14 C44/R13 C45/R12 C46/R11 C47/R10 C48/R9 C49/R8 R15/R7 R14/R6 R13/R5 R12/R4 R11/R3 R10/R2 R9/R1 R8/R0 VLC5 VLC1 NC VLC4
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 1 64 63 2 62 3 61 4 5 60 6 59 58 7 57 8 9 56 55 10 11 54 53 12 52 13 51 14 50 15 49 16 48 17 47 18 46 19 45 20 44 21 43 22 42 23 41 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
C37 C36 C35 C34 C33 C32 C31 C30 C29 C28 C27 C26 C25 C24 C23 C22
C21 C20 C19 C18 C17 C16 C15 C14 C13 C12 C11 C10 C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 NC CLOCK
Remark /xxx indicates active low signal.
2
VLC2 VLC3 D0/SI D1(P, /S) D2(CAE) D3/SO SYNC /BUSY VDD VSS /STB, /SCK C, /D CA0 CA1 /CS RESET
Data Sheet S10299EJ4V0DS00
BLOCK DIAGRAM
R0/R8 to R7/R15 8 R-S ROW DRIVER R-NS 16
R8/C49 to R15/C42 8 ROW/COLUMN DRIVER 16 8 16
C0 to C41 42 C-S COLUMN DRIVER C-NS
42
VDD
50 R-S DATA MEMORY BANK 0 (50 x 8 BITS)
50 DATA MEMORY BANK 1 (50 x 8 BITS) 8
VLC1 VLC2 VLC3 VLC4 VLC5
LCD R-NS VOLTAGE C-S CONTROL C-NS
Data Sheet S10299EJ4V0DS00
16
VSS LCD TIMING SYNC CONTROL 16
COMMAND DECODER
DATA POINTER
CHARACTER GENERATOR (160 x 5 x 7 BITS)
7
8
8
8
8 STOP SYSTEM CLOCK CONTROL SERIAL/PARALLEL INTERFACE
CLOCK
CLOCK BUFFER
PD16434
/STB, /SCK
RESET
/CS
CA1
CA0
C, /D
/BUSY
D3/SO
D2(CAE)
D1(P, /S)
D0/SI
3
PD16434
TABLE OF CONTENTS
1. PIN FUNCTIONS ............................................................................................................ 6
1.1 D0 to D3 (Data Bus) ... 3-state input/output ................................................................................. 6 1.2 SI (Serial Data In) ... Also serves as D0 input .............................................................................. 6 1.3 SO (Serial Data Out) ... Also serves as D3 output ........................................................................ 6 1.4 P, /S (Parallel/Serial Select) ... Also serves as D1 input ............................................................... 6 1.5 CAE (Chip Address Enable) ... Also serves as D2 input ............................................................... 6 1.6 CA0, CA1 (Chip Address) ... Input ............................................................................................. 6 1.7 /CS (Chip Select) ... Input ......................................................................................................... 7 1.8 /STB, /SCK (Strobe/Serial Clock) ... Input ................................................................................... 7 1.9 C, /D (Command/Data) ... Input ................................................................................................. 7 1.10 /BUSY (Busy) ... 3-state output ............................................................................................... 1.12 C0 to C41 (Column) ... Output ................................................................................................. 7 9 1.11 SYNC (Synchronous) ... 3-state input/output ............................................................................ 8 1.13 R8/C49 to R15/C42 (Row/Column) ... Output .............................................................................. 9 1.14 R0/R8 to R7/R15 (Row) ... Output ............................................................................................. 9 1.15 VLC1 to VLC5 (LCD Drive Voltage Supply) ... Input ....................................................................... 9 1.16 CLOCK (Clock) ... Input ......................................................................................................... 9 1.17 RESET (Reset) ... Input .......................................................................................................... 9 1.18 VDD ....................................................................................................................................... 9 1.19 VSS ....................................................................................................................................... 9
2. INTERNAL BLOCK FUNCTIONS ......................................................................................
10
2.1 Serial/Parallel Interface ............................................................................................................ 10 2.2 Command Decoder ................................................................................................................. 11 2.3 Character Generator ............................................................................................................... 11 2.4 Data Pointer ........................................................................................................................... 14 2.5 Data Memory .......................................................................................................................... 15 2.6 LCD Voltage Control Circuit ..................................................................................................... 19 2.7 LCD Timing Control Circuit ...................................................................................................... 19 2.8 Row/Column Driver ................................................................................................................. 19
3. DATA INPUT/OUTPUT OPERATION ................................................................................. 21 4. SELECTING PD16434 INTERFACE FUNCTION WITH CPU ................................................ 27
4.1 Functions of Shared Pins ......................................................................................................... 27 4.2 Chip Address Selection Function .............................................................................................. 28
5. LCD DRIVE REFERENCE VOLTAGE SUPPLY .................................................................... 29
5.1 Supplying LCD Drive Reference Voltage by Resistor Network ...................................................... 29 5.2 Reduction in Current Consumption by RESET Signal .................................................................. 30
6. DISPLAY EXAMPLES ..................................................................................................... 31 7. STANDBY MODE ........................................................................................................... 35
7.1 Clearing Standby Mode ........................................................................................................... 35
4
Data Sheet S10299EJ4V0DS00
PD16434
7.2 Stopping Clock Supply and Retaining Data at Low Voltage in Standby Mode ............................ 36
8. RESET OPERATION .................................................................................................. 38 9. COMMANDS ............................................................................................................ 40
9.1 LCD Display Mode Setting Commands ................................................................................. 9.2 Data Pointer Load Command .............................................................................................. 40 42 9.3 Data Processing Mode Setting Commands ........................................................................... 42 9.4 Memory Bit Manipulation Commands ................................................................................... 45 9.5 Standby Operation Setting Command .................................................................................. 47
10. SYSTEM CONFIGURATION EXAMPLE ....................................................................... 48 11. ELECTRICAL SPECIFICATION .................................................................................. 49 12. PACKAGE DRAWINGS ............................................................................................. 60 13. RECOMMENDED SOLDERING CONDITIONS .............................................................. 62
Data Sheet S10299EJ4V0DS00
5
PD16434
1. PIN FUNCTIONS
1.1 D0 to D3 (Data Bus) ... 3-state input/output In the parallel interface mode, these pins serve as 4-bit parallel data input/output pins. Data on the D0 to D3 lines is read at the /STB signal rising edge. The 4-bit data, read at the first rising edge of the /STB, is loaded into the upper 4 bits of the serial/parallel register, and the data read at the second rising edge is loaded into the lower 4 bits of the register. The serial/parallel register contents are output to the D0 to D3 pins in synchronization with the /STB signal falling edge. In the same manner as read operation, the upper 4 bits of the serial/parallel register are output in the first /STB signal falling edge, and the lower 4bits are output in the second /STB falling edge. In the serial interface mode, the D0 serves as the serial data input pin (SI), and the D3 pin serves as the serial data output pin (SO). The D1 pin serves as the parallel/serial interface mode selection pin (P, /S), and the D2 pin serves as the chip address enable pin (CAE). 1.2 SI (Serial Data In) ... Also serves as D0 input This pin serves as the serial data input pin in the serial interface mode. Data on the SI line is loaded into the serial/parallel register at the /SCK rising edge. The first data becomes the MSB. This is a Schmitt trigger input with hysteresis, in order to prevent erroneous operation caused by noise. 1.3 SO (Serial Data Out) ... Also serves as D3 output This pin serves as the serial data output pin in the serial interface mode. The serial/parallel register contents are output to the SO pin with the MSB first in synchronization with the /SCK pin falling edge. 1.4 P, /S (Parallel/Serial Select) ... Also serves as D1 input This pin is sampled at the RESET signal falling edge (when the reset is released). If this pin is high, the parallel interface mode is set. If it is low, the serial interface mode is set. This is a Schmitt trigger input with hysteresis in order to prevent erroneous operation caused by noise. 1.5 CAE (Chip Address Enable) ... Also serves as D2 input The CAE input has a meaning, if P, /S input is low (when the serial interface mode is specified) at the RESET signal falling edge (when reset is released). If the CAE signal is high at this timing, the chip address function is enabled. If the CAE signal is low, the chip address function is disabled. This is a Schmitt trigger input with hysteresis in order to prevent erroneous operation caused by noise. 1.6 CA0, CA1 (Chip Address) ... Input This is the input pin used to allocate the inherent address to select each PD16434 chip, when interfacing with the CPU in a multi-chip configuration. In the parallel interface mode, CA0 and CA1 inputs are compared with the chip address information sent from the CPU, regardless of the CAE input. In the serial interface mode, these inputs are compared with the chip address information sent from the CPU, when the chip address selection function is enabled by the CAE input.
6
Data Sheet S10299EJ4V0DS00
PD16434
Table 1-1. Processing CA1, CA0 Pins Mode With chip address function - Always in parallel mode - When CAE = 1 in serial mode Without chip address function - When CAE = 0 in serial mode Remark In a multi-chip configuration in the serial interface mode, chip selection is also possible by providing decoded /CS signals for the number of chips used, without using the chip address function. In this case, CAE for each chip must be set to 0, and CA1 and CA0 pins must be set to 00. These are Schmitt trigger inputs with hysteresis in order to prevent erroneous operation caused by noise. 1.7 /CS (Chip Select) ... Input This is the chip select input, which is low active. When the chip address function is not used, if a low is input to the /CS input, the /STB, /SCK and C, /D inputs become effective, so that commands and data can be input/output. When the chip address function is used, in order for the /STB, /SCK and C, /D inputs to become effective, the chip address information and CA0 and CA1 inputs must coincide, and moreover, the /CS input should become low. When the /CS input is set to high, D3-D0 and /BUSY pins unconditionally become high impedance. This is a Schmitt trigger input with hysteresis in order to prevent erroneous operation caused by noise. 1.8 /STB, /SCK (Strobe/Serial Clock) ... Input In the parallel interface mode, this pin serves as the strobe signal input pin (STB) for 4-bit parallel data input/output operation. In the serial interface mode, this pin serves as the serial clock input pin (/SCK) for serial data input/output operation. 1.9 C, /D (Command/Data) ... Input This pin is used to identify whether serial or parallel data input is a command or data. When inputting a command, set the C, /D pin to high. When inputting data, set to low. When inputting a command or data in the parallel interface mode, the command or data is latched at the second /STB rising edge. In the serial interface mode, the command or data is latched at the rising edge of the 8th /SCK. However, in parallel input, switching C, /D must be performed, before the falling edge of the 1st /STB. When outputting data, C, /D input must always be set to low, regardless of whether the mode is parallel or serial. This is a Schmitt trigger input with hysteresis in order to prevent erroneous operation caused by noise. 1.10 /BUSY (Busy) ... 3-state output This pin outputs a /BUSY signal which indicates to the CPU that the PD16434 is busy because of internal processing. If this signal is low, PD16434 is busy, and the CPU cannot execute read/write to the PD16434. The /BUSY signal becomes low at second rising of the /STB signal in the parallel interface mode. In the serial interface mode, the /BUSY signal becomes low at the rising edge of the 8th /SCK. The PD16434 sets the /BUSY signal to high, when the PD16434 completes the internal processing. The /BUSY output becomes high impedance, when the chip is not selected (/CS = high or the chip address does not coincide). Always set to 00 CA1, CA0 Set to 00, 01, 10, or 11 (always 00 in single chip configuration)
Data Sheet S10299EJ4V0DS00
7
PD16434
1.11 SYNC (Synchronous) ... 3-state input/output In a multi-chip configuration, in which the row drive signal is commonly used, this pin inputs/outputs the synchronous signal in order to synchronize the phases of all LCD drive alternate cycle signals (row/column signals) with the frame period. One chip in the multi-chip configuration is selected as the master, and the SYNC pin of the master is set to the output mode. The remaining chips all serve as slave chips, and these SYNC pins are set to the input mode. The SMM command is used to specify whether the pin functions as an input or output pin. The master chip, set in the output mode, outputs the SYNC pulse in the last cycle in each frame. A slave chip reads the SYNC pulse output from the master chip for synchronization with the master chip. Figure 1-1 and Figure 1-2 show SYNC pulse output timing waveforms in 8-time-division and 16-time-division modes, respectively. In single chip configuration, the SYNC pin can be set in either the input or output mode. However, when it is set in the input mode, the SYNC pin must be fixed to VSS. If it is set in the output mode, the SYNC pin must be left open. Figure 1-1. SYNC Signal in 8-Time-Division Mode
1 frame
ROW0
SYNC
Figure 1-2. SYNC Signal in 16-Time-Division Mode
1 frame
ROW0
SYNC
8
Data Sheet S10299EJ4V0DS00
PD16434
1.12 C0 to C41 (Column) ... Output These pins serve as LCD column drive signal output pins. 1.13 R8/C49 to R15/C42 (Row/Column) ... Output These pins serve as LCD row drive signals R8 to R15 or column drive signals C49 to C42 output pins. Whether or not these pins are used as row or column pins is specified by the SMM command. 1.14 R0/R8 to R7/R15 (Row) ... Output These pins serve as LCD row drive signals R0 to R7 or R8 to R15. Whether or not these pins are used as R0 to R7 or R8 to R15 is specified by the SMM command. 1.15 VLC1 to VLC5 (LCD Drive Voltage Supply) ... Input These pins input the reference voltage for determining the LCD row/column drive signal voltage level. 1.16 CLOCK (Clock) ... Input This pin inputs the external clock. 1.17 RESET (Reset) ... Input This is the high active reset signal input pin. The reset operation has priority over all other operations. This input is also used for cleaning the standby mode or operation to retain data in the data memory at a low power supply voltage. 1.18 VDD Positive voltage power supply pin. 1.19 VSS Ground pin.
Data Sheet S10299EJ4V0DS00
9
PD16434
2. INTERNAL BLOCK FUNCTIONS
2.1 Serial/Parallel Interface The PD16434 contains both serial and parallel interface functions. Whether the serial interface or the parallel interface is used is determined by whether the P, /S input is high (specifying the parallel interface) or low (specifying the serial interface) at the RESET signal falling edge. The interface circuit is used to write commands and data from the CPU or output data to the CPU. The operation of the serial/parallel interface differs, depending on the data processing mode setting. When a RESET is input, the data processing mode is initialized to the write mode, so that the first command input can be accepted. Afterwards, the mode can be set to write related or read related data processing mode by the data processing set command. If the data processing mode is set to the write, AND, OR, or the character write related mode, the serial/parallel interface is set to the data input mode, and the PD16434 clocks in the data from the SI pin (serial data) or from the D3 to D0 pins (4-bit parallel data) in synchronization with the rising edge of the /SCK or the /STB, respectively. If the data processing mode is set to the read mode, the serial/parallel interface becomes the data output mode and outputs data from the SO pin (serial data) or from the D3 to D0 pins (4-bit parallel data) in synchronization with the falling edge of the /SCK or the /STB. The serial/parallel register serves as the buffer, between 8-bit serial data or two 4-bit parallel data transferred through the serial input/output (SI, SO) or parallel input/output (D3 to D0) and 8-bit parallel data of the data memory. Figure 2-1. Serial/Parallel Interface
Internal bus 8 /STB, /SCK RESET /CS CA0,CA1 C, /D /BUSY Read/write control /STB' /SCK' SI' 8-bit serial/parallel register bit 0-3 4 bit 4-7 4 SO'
D0/SI D1(P, /S) D2(CAE) D3/SO Data control
10
Data Sheet S10299EJ4V0DS00
PD16434
If the C, /D input indicates command specifications, the data input from the CPU to the serial/parallel interface is sent from the serial/parallel register to the command decoder for decoding. In the write mode, if the C, /D input indicates data specifications, the data loaded to the serial/parallel register is directly transferred to the data memory. In the AND or OR mode, the data loaded into the serial/parallel register is ANDed or ORed with the data memory contents, and the result is transferred to the data memory. In the character mode, the data loaded into the serial/parallel register is regarded as ASCII or JIS code and is sent to the character generator. It is decoded to 5 x 7-bit character display pattern, and is stored into 5 successive data memory addresses. Only when set to the read mode, can the serial/parallel interface output data to the CPU. When set to the read mode, the serial/parallel interface always reads 8-bit data from the data memory and sets it in the serial/parallel register for the next read operation. In the serial interface mode, the data in the serial/parallel register is output from the SO pin with the MSB first at each /SCK falling edge. In the parallel interface mode, the upper 4 bits of the data in the serial/parallel register are output from the D3 to D0 pins at the first falling edge of the /STB, and the lower 4 bits of the data in the serial/parallel register are output from those pins at the second falling edge of the /STB. In either the serial/parallel interface mode, each time 8 bits of data are output, the next 8 bits of data are automatically read out from the data memory and set in the serial/parallel register. 2.2 Command Decoder If the 8-bit data, input through the serial/parallel interface, is specified as a command (C, /D = 1), the data is clocked in as a command, and is decoded to generate an internal control signal. 2.3 Character Generator The character generator becomes effective, when a character mode setting command (SCML, SCMR) is executed. In this case, 8-bit data written through the serial/parallel interface is interpreted as a character code, and the 5 x 7-dot matrix pattern, corresponding to the code, will be generated. It is transferred to the 5 successive addresses in the data memory (7 bits x 5 times). The character generator contains the following 160 different pattern data :
ASCII Upper-case alphabets 26 Lower-case alphabets 26 Numerical characters Symbols 10 34 KATAKANA 55 Symbols 9
JIS
Figure 2-2 shows correspondence of character codes (ASCII/JIS) and 5 dots x 7 dots display patterns. 96 codes of 20H to 7FH correspond to ASCII characters, and A0H to DFH correspond to JIS characters.
Data Sheet S10299EJ4V0DS00
11
PD16434
Figure 2-2. Character codes and Display Pattern (Standard ROM code: 001)
7 40 3 Character code
0 0 0 0 0010
0 0 0 1
0 0 1 0
0 0 1 1
0 1 0 0
0 1 0 1
0 1 1 0
0 1 1 1
1 0 0 0
1 0 0 1
1 0 1 0
1 0 1 1
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
0011
0100
0101
0110
0111
1010
1011
1100
1101
12
Data Sheet S10299EJ4V0DS00
PD16434
Figure 2-3 shows the LCD configuration for the character generator. A character is configured in 5 x 7-dot configuration. The most significant bit (bit 7) of the data memory is not used by the character generator. Therefore, LCD dots, corresponding to the most significant bit (R7 in 8-time-division, or R7 and R15 in 16-time-division), can be used for the cursor or indicator display pattern, independently from the character generator. The most significant bits are manipulated by a cursor manipulation command (WRCURS, CLCURS), etc.
Figure 2-3. LCD Configuration When Using Character Generator
(a) 8-time-division R0 R1 R2 R3 R4 R5 R6 R7 Cn+3 Cn+4 Cn+2 Cn+1 Cn (b) 16-time-division R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 Cn+3 Cn+4 Cn+2 Cn+1 Cn
Data Sheet S10299EJ4V0DS00
13
PD16434
2.4 Data Pointer The data pointer consists of a 6-bit binary counter (DP5 to DP0) and 1-bit bank flag (BNKF). It specifies the data memory address.
Figure2-4. Data Pointer Organization
6-bit binary counter
BNKF
DP5
DP4
DP3
DP2
DP1
DP0
The contents of the bank flag and the 6-bit binary counter are set simultaneously by the immediate data from the LDPI command. The bank flag contents specify the data memory bank (BNKF=0 : Bank 0, BNKF=1 : Bank 1), and the 6-bit binary counter contents specify the address (00H to 31H) in the bank specified by the bank flag. The 6-bit binary counter is an up/down counter. Its contents are modified (+1, -1, or held) each time a read, write, or AND operation is performed, or an 8-bit data is input/output in the OR mode, according to the specifications for each mode setting command. When the BSET or BRESET command is executed, the 6-bit binary counter contents are modified (+1, -1, or held) each time according to the command specification. In addition, in the character mode, the 6-bit binary counter contents are modified (+5, -5) each time an 8-bit data is input or a cursor processing command is executed.
Remark
The 6-bit binary counter value can exceed the limit of the data memory address space. For example, if the 6-bit binary counter is decremented (-1) from 00H, the value will be 3FH, or it is incremented (+1) from 31H, the value will be 32H. However, the data memory will perform nothing for the command specifying an address from 32H to 3FH.
14
Data Sheet S10299EJ4V0DS00
PD16434
2.5 Data Memory The data memory is a static RAM configured by two 50-word x 8-bit banks. It is used for storing display data.
Figure 2-5. Data Memory Configuration
00H
Bank 0 (50 x 8) 31H 00H Bank 1 (50 x 8)
31H
The data memory bank is specified by the bank flag in the data pointer, and the address in the bank is specified by the 6-bit binary counter in the data pointer. The 8-bit data, written to the serial/parallel interface by the CPU, is used for operation or decoded according to the specified data processing mode, and is written into the data memory. The data memory contents can be directly manipulated by a bit manipulation instruction. When the PD16434 is set in the read mode, the data memory contents are output to the CPU through the serial/parallel interface. The data memory contents are read out in bit units in synchronization with the row drive signal and are sent to the column driver for driving the LCD. This operation is performed independently from command/data write/read operation with the CPU, which is performed through the serial/parallel interface. Display data read out operation differs, depending on the number of time-divisions.
(1) 8-time-division (single/multi-chip configuration) The contents of the display data in bank 0 or bank 1, whichever is specified by the SMM command, are read out to the column driver. Figure 2-6 shows bits correspondence for the row driver and column driver for the data memory. If the data located at the Rn and Cm intersection is 1, the corresponding LCD dot is ON. If the data is 0, the dot is OFF.
Data Sheet S10299EJ4V0DS00
15
PD16434
Figure 2-6. Data Memory (8-Time-Division, Single/Multi-Chip)
31H bit 0 1 2 3 4 5 6 7 30H 01H 00H R0 R1 R2 R3 R4 R5 R6 R7 Corresponding row signal
C49
C48
C1
C0
To column driver
16
Data Sheet S10299EJ4V0DS00
PD16434
(2) 16-time-division (single-chip configuration) Bank 0 and bank 1 are used in a pair, and the contents are read out to the column driver as 42 x 16-bit display data. Figure 2-7 shows correspondence of bits for the row driver and column driver for the data memory. If the data located at the Rn and Cm intersection is 1, the corresponding LCD dot is ON. If the data is 0, the dot is OFF.
Figure 2-7. Data Memory (16-Time-Division, Single-Chip)
29H bit 0 1 2 3 Bank 0 4 5 6 7 0 1 2 3 Bank 1 4 5 6 7 28H 01H 00H R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 Corresponding row signal
C41
C40
C1
C0
To colmn driver
Data Sheet S10299EJ4V0DS00
17
PD16434
(3) 16-time-division (multi-chip configuration) Bank 0 and bank 1 are used in a pair, and the contents are read out to the column driver as 50 x 16-bit display data. The row driver signals, output from each PD16434, are R0 to R7 or R8 to R15. Figure 2-8 shows bits correspondence for the row driver and column driver for the data memory for each chip.
Figure 2-8. Data Memory (16-Time-Division, Multi-chip)
31H bit 0 1 2 3 Bank 0 4 5 6 7 0 1 2 3 Bank 1 4 5 6 7 30H 01H 00H R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 Corresponding row signal
C49
C48
C1
C0
To colmn driver
18
Data Sheet S10299EJ4V0DS00
PD16434
2.6 LCD Voltage Control Circuit This circuit multiplexes the DC voltage supplied from the LCD drive reference voltage inputs (VLC1 to VLC5) with the AC signal synchronized with the CLOCK and SYNC signal, and supplies the signals to determine the select and non-select level of the row and column signals and the phase for the row and column drivers. Table 2-1 indicates these signal levels and the phase.
Table 2-1. LCD Driver Voltage Signal Levels and Phase
8-time-divisions
-
Row Select Non-select Column Select Non-select VLC0 VLC4 VLC5 VLC2
Note
16-time-divisions
-
VLC0 VLC4 VLC5 VLC3 VLC5 VLC1 VLC0 VLC2
+
VLC5 VLC1 VLC0 VLC2
+
Note VLC2 = VLC3 2.7 LCD Timing Control Circuit This circuit generates the timing signals from the clock signal, according to the frame frequency specified by the SFF command, and the number of time divisions specified by the SMM command. The timing signals are necessary for automatically reading the display data and driving the LCD, and are supplied to the data memory row/column driver, and LCD voltage control circuit. If the SYNC signal is set to the output mode by the SMM command, the SYNC signal is output for each frame. If the SYNC mode is specified to the input mode, the SYNC signal supplied from some other chip is input to generate the timing signals in synchronization with each frame interval. The SYNC signal input/output function is used to synchronize the LCD drive timing between chips in multi-chip configuration. 2.8 Row/Column Driver The row/column driver consists of the column driver for C0 to C41 signals, row/column driver for R15 to R8 and C42 to C49, and a dual mode row driver for R0 to R7 or R8 to R15. The dual mode row driver function is determined by the SMM command.
Data Sheet S10299EJ4V0DS00
19
PD16434
Table 2-2. LCD Dual Mode Row Driver Function Selection
M2, M1, M0
Note 1
Number of time divisions
R0/R8 to R7/R15
R15/C42 to R8/C49
000 001 010 011 100 101 110 111
8
R0 to R7
C42 to C49
16
R8 to R15
Note 2
R0 to R7
Note 3
R15 to R8
Notes 1. M2, M1, M0 is code specified by SMM command. 2. Some other chip handles R0 to R7 outputs. 3. Some other chip handles R8 to R15 outputs. M2, M1, M0 = 111 is for single chip configuration. In this case, R15/C42 to R8/C49 are used as row signal outputs, and all 16 row signals are output from this chip.
These drivers perform switching of the analog level in correspondence to the contents of the display data read out from the data memory and the timing signals supplied from the LCD timing control circuit, according to the select level, non-select level, and phase supplied from the LCD voltage control circuit, and generates and outputs row and column driver signals in order to directly drive the LCD.
20
Data Sheet S10299EJ4V0DS00
PD16434
3. DATA INPUT/OUTPUT OPERATION
In the PD16434, a command/data consists of 1 byte (8 bits), and processing is performed each time a byte of data is transferred in either the serial or parallel mode. The end of a byte data transfer is confirmed by the byte counter (octal/binary counter) which counts eight /SCK counts or two /STB counts. This counter is unconditionally cleared, when /CS = high or RESET = high, and becomes ready to count a new byte or data. Therefore, if /CS is set to high or RESET is input in the middle of a byte transfer, the byte transfer is not guaranteed. In the serial interface mode, data is treated as 8-bit serial data. It is regarded that 1 byte of data has been input or output, when eight serial clock pulses (/SCK) are counted in the chip selected condition, then internal processing is started. At the 8th rising edge of the /SCK, the PD16434 sets the /BUSY signal to low to inform the CPU that the
PD16434 is in a busy state.
When the internal processing completes, the PD16434 sets the /BUSY signal to high to inform the CPU that the
PD16434 is ready for the next byte transfer.
The serial data is input/output with the MSB first (refer to Figure 3-1 and Figure 3-2). If the chip address selection function is specified in the serial interface mode, the 8-bit serial data (only the lower 2 bits have a meaning) for chip address information must be written first after the /CS falling edge. Only the chip, whose address coincides with this information, can enter command input or data input/output operation (refer to Figure 3-3 and Figure 3-4). In the parallel interface mode, since the data bus (D3 to D0) is a 4-bit bus, data is treated as 4-bit x 2 parallel data. When the parallel data strobe signal (/STB) is counted twice in the chip selected state, it is regarded that a byte of data has been input/output, then the PD16434 enters the internal processing. At the 2nd rising edge of the /STB, the PD16434 sets the /BUSY signal to low, to inform the CPU that the
PD16434 is in a busy state. When the internal processing completes, the PD16434 sets the /BUSY signal to high, to
inform the CPU that the PD16434 is ready for the next byte transfer. In both input and output operation, the upper 4 bits of parallel data correspond to the first /STB, and the lower 4 bits of parallel data correspond to the second /STB. The parallel interface of the PD16434 is compatible with the PD82C43 I/O expander, so that the parallel data can be input to the PD16434 in the same manner as sending 4-bit data twice to the PD82C43. In addition, 8-bit data can be read out from the serial/parallel register of the PD16434 in the same way as reading 4-bit data twice from the
PD82C43.
The chip address selection function is always specified in the parallel interface mode. After the /CS falling edge, the data on the D1 and D0 lines, read at the first falling edge of the /STB, becomes the chip address information. The lower 2 bits of the command code, output from the CPU as the data for selecting port 4 to port 7 of the PD82C43, are used as the chip address information. After the /CS falling edge, the command code, output from the CPU at the second and successive falling edges of the /STB, has no meaning for the PD16434 (refer to Figure 3-5 and Figure 3-6). Refer to 4. SELECTING PD16434 INTERFACE FUNCTION WITH CPU for details on chip address function selection.
Data Sheet S10299EJ4V0DS00
21
PD16434
Figure 3-1. Serial Input Timing Waveforms (Without Chip Address Selection Function)
/CS
/SCK
SI MSB LSB
C, /D
/BUSY
Internal processing time
Figure 3-2. Serial Output Timing Waveforms
/CS
/SCK
SO MSB /BUSY LSB
Internal processing time C, /D
22
Data Sheet S10299EJ4V0DS00
Figure 3-3. Serial Input Timing Waveforms (With Chip Address Selection Function)
/CS
/SCK
7th SI
Data Sheet S10299EJ4V0DS00
8th
MSB Chip address To all chips To newly selected chip
LSB
C, /D
/BUSY
Hi-Z /BUSY output for chip that was selected before /CS was set to high
/BUSY output for selected chip
/BUSY output for newly selected chip
PD16434
Same chip
23
24 Figure 3-4. Serial Output Timing Waveforms (With Chip Address Selection Function)
/CS /SCK 7th SI
Data Sheet S10299EJ4V0DS00
8th
Chip address To all chips
SO MSB From newly selected chip LSB
C, /D
/BUSY
Hi-Z /BUSY output for chip that was selected before /CS was set to high
/BUSY output for selected chips
/BUSY output for newly selected chip
PD16434
PD16434
Figure 3-5. Parallel Input Timing
/CS
/STB
1st
2nd
D3 to D0
Chip address
Upper 4 bits
Invalid data
Lower 4 bits
CPU16434 CPU16434
CPU16434 CPU16434
C, /D
/BUSY /BUSY output for newly selected chip
/BUSY output for chip that was selected before /CS was set to high
Data Sheet S10299EJ4V0DS00
25
PD16434
Figure 3-6. Parallel Output Timing
/CS
"L"
/STB
1st
2nd
D3 to D0
Invalid data
Upper 4 bits
Invalid data
Lower 4 bits
CPU16434 16434CPU
CPU16434 16434CPU
/BUSY
Internal processing time C, /D
26
Data Sheet S10299EJ4V0DS00
PD16434
4. SELECTING PD16434 INTERFACE FUNCTION WITH CPU
The command/data for the PD16434 is 8 bits long. However, serial interfacing with the CPU is made in 8-bit transfer or parallel interfacing is made in two 4-bit transfers. In addition, the PD16434 is provided with a chip address selection function for multi-chip system configuration. Whether the serial or parallel interface is used and whether or not the chip address select function is used are specified by the data on the D2 (CAE) line and D1 (P, /S) line at the RESET signal release timing (falling edge).
Figure 4-1. Interface Specification Timing Waveforms
RESET
D2(CAE) D1(P, /S)
Table 4-1. Interface Specification Code D2(CAE) D1(P, /S) Serial/parallel specification 0 1 0/1 0 0 1 Parallel Serial Chip address selection function Unprovided Provided
4.1 Functions of Shared Pins The function of the /STB, /SCK, D3/SO, and the D0/SI pins used for clock input and data input/output differ, depending on whether the serial interface or the parallel interface is specified, as indicated in Table4-2.
Table 4-2. Function of Shared Pins Pin name /STB, /SCK D3/SO D2(CAE) D1(P, /S) D0/SI SI input Serial (P, /S = 0) /SCK input SO output - - Parallel (P, /S = 1) /STB input D3 to D0 input/output (4-bit parallel data bus)
Data Sheet S10299EJ4V0DS00
27
PD16434
4.2 Chip Address Selection Function In a multi-chip system configuration, the chip address selection function compares the chip address assigned to each PD16434 (by CA0, CA1 inputs) in advance and the chip address information (2 bits) sent from the CPU in the serial or parallel data format. Only the chip whose address coincides with the chip address information is seleceted (enables command/data input/output). Thus, the CPU need not send two or more chip select signals (/CS). This function is unconditionally provided in the parallel interface mode. However, in the serial interface mode, this function is provided, when D2(CAE) = 1 (at reset release), is specified. (1) Parallel interface mode (refer to Figure 3-5 and Figure 3-6) After the falling edge of the /CS, the data read into D1 (corresponds to CA1) and D0 (corresponds to CA0) at the first falling edge of the /STB becomes the 2-bit chip address information. The parallel interface is equivalent to that for the PD82C43 I/O expander. Therefore, the chip address information (0 to 3) for the PD16434 can be obtained on the D1 and D0 lines at the falling edge of the /STB by executing an output or input instruction for port 4 to port 7 of the PD82C43, when the PD50H is connected to the
PD16434 using the PD82C43 interface function.
(2) Serial interface mode (refer to Figure 3-3 and Figure 3-4) After the falling edge of the /CS, the data read in to SI at the rising edge of the 7th /SCK (corresponds to CA1) and 8th /SCK (corresponds to CA0), that is the lower 2 bits of the first 8-bit serial data, becomes the chip address information. Remarks 1. When a RESET is input, the chip address comparison data (data compared with CA1 and CA0) in the
PD16434 is cleared to "00". Therefore, in multi-chip configuration, if the /CS is set to low
immediately after the RESET input is released, a chip whose CA1 and CA0 are set to "00" sets the /BUSY to high, informing the CPU that the chip can be accessed. If no chip address is sent, a chip whose CA1 and CA0 are "00" will be accessed. 2. The following points must be noted for a multi-chip configuration system using the parallel interface; when transferring the process from chip A, which has already been in the read mode to chip B, and again selecting chip A after that, the data pointer must be set by the data pointer load command reading data.
28
Data Sheet S10299EJ4V0DS00
PD16434
5. LCD DRIVE REFERENCE VOLTAGE SUPPLY
The value of the LCD drive reference voltage to the PD16434 differs, depending on whether the number of time divisions is 8 or 16, so that the LCD drive reference voltage should be set as shown in Figure 5-1 and Figure 5-2. Figure 5-1. 8-Time-Divisions
VDD VDD - 1 VLCD 4 PD16434 VLC3 3 VDD - 4 VLCD VDD - VLCD VLC4 VLC5
Figure 5-2. 16-Time-Divisions
(VLC0)VDD VLC1 VLC2 PD16434 VLC3 VLC4 VLC5
(VLC0) VDD VLC1 VLC2
VDD VDD - 1 VLCD 5
2 VDD - 4 VLCD
2 VDD - 5 VLCD VDD - 3 VLCD 5 VDD - 4 VLCD 5 VDD - VLCD
Remark For both 8 and 16-time-divisions, the LCD drive voltage (LLCD) must not exceed VDD.
5.1 Supplying LCD Drive Reference Voltage by Resistor Network Figure 5-3 and Figure 5-4 show circuit examples, which supply the LCD drive reference voltage indicated in Figure 5-1 and Figure 5-2 using register networks which divide the voltage level between VDD and VSS. Figure 5-3. 8-Time-Divisions Circuit Example Figure 5-4. 16-Time-Divisions Circuit Example
(VLC0) VDD R1 VLC1 R1 VLC2 PD16434
VDD
(VLC0) VDD R1 VLC1 R1 VLC2 R1 PD16434
VDD
VLC3 R1 VLC4 R1 VLC5 R2 VSS -6.0 V
VLC3 R1 VLC4 R1 VLC5 R2 VSS -6.0 V
The values of R1 and R2, which divide the voltage for 8-time-divisions and 16-time-divisions, are determined by the following expressions: R1 =
VLCD x R2 (8-time-divisions) 4(V - VLCD)
DD
Data Sheet S10299EJ4V0DS00
29
PD16434
R1 =
VLCD x R2 (16-time-divisions) 5(VDD - VLCD)
5.2 Reduction in Current Consumption by RESET Signal If a resistor network is used to supply the LCD drive reference voltage, some current is drained by the resistor network connected across VDD and VSS when no display operation is performed, such as when the PD16434 is in the STOP mode or when it is being reset. Therefore, for a system to which reducing the current draw is extremely important, the current path thorough the resistor network must be cut off by an external circuit, when no displaying is performed, to eliminate unnecessary current flow. Figure 5-5 shows a circuit which cuts off the current to the resistor network during reset state (RESET = high) using the the RESET signal level instead of the VSS level. Figure 5-5. Example of Controlling Current Path Using RESET Signal
VDD VDD VDD (VLC0) VLC1 VLC2 CPU VLC3 VLC4 VLC5 Output port RESET PD16434
Remark The power to the CPU and the PD16434 must be from the same source.
30
Data Sheet S10299EJ4V0DS00
PD16434
6. DISPLAY EXAMPLES
Figure 6-1 shows how the data memory contents and LCD display pattern are corresponded, when displaying characters "AEZ" in 8-time-division mode. This example is to display 3 digits of 5x7 (5x8) dot characters, and uses data memory addresses 00H to 0EH (0 to 14) and column signals C0 to C14. Figure 6-2 shows the timing waveforms for displaying character "A" in columns C14 to C10 for the display example, shown in figure 6-1. Figure 6-3 shows how the data memory contents and display pattern are corresponded, when displaying characters " ANZ " in 16-time-division mode. This example is to display 5 x 7 (5 x 8) dot characters in two rows, 3 digits in each row, and uses data memory addresses 00H to 0EH (0 to 14) in data memory banks 0 and 1 and column signals C0 to C14. Figure 6-4 shows the timing waveforms for displaying character " 8 " in columns C14 to C10 for display example, shown in Figure 6-3. In Figure 6-2 and Figure 6-4, when the differential waveform levels between the row signal and column signal are VLCD and -VLCD, the LCD dot corresponding to these signals will be lit. Figure 6-1. 8-Time-divisions
PD16434 Bank 0/1 0 1 1 1 1 1 1 0 1 0 0 1 0 0 0 0
Note
8, 5
A
Timing strobe
data memory address 9 1 1 1 1 1 1 1 0 8 1 0 0 1 0 0 1 0 7 1 0 0 1 0 0 1 0 6 1 0 0 1 0 0 1 0 5 1 0 0 0 0 0 1 0 4 1 0 0 0 0 1 1 0 3 1 0 0 0 1 0 1 0 2 1 0 0 1 0 0 1 0 1 1 0 1 0 0 0 1 0 0 1 1 0 0 0 0 1 0 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 1 0 0 1 0 0 0 0 0 1 1 1 1 1 1 0
14 13 12 11 10 1 0 0 1 0 0 0 0
R2/R10
R3/R11
R4/R12
R5/R13
R6/R14
Note Display data is read out from either bank 0 or bank 1.
R7/R15
R0/R8
R1/R9
C14
C13
C12
C11
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
C0
Data Sheet S10299EJ4V0DS00
31
PD16434
Figure 6-2. 8-Time-divisions (When Displaying Character A)
1 frame
7 VDD VLC1 ROW 0 VLC2 VLC3 VLC4
0
1
2
3
4
5
6
7
0
1
VDD VLC1 ROW 1 VLC2 VLC3 VLC4
VDD VLC1 ROW 7 VLC2 VLC3 VLC4
VDD
C10, C14
VLC2
VLC4 VDD
C11, C12, C13
VLC2
VLC4
VLCD
1/4 VLCD -1/4 VLCD
ROW 0 to C13
-VLCD
32
Data Sheet S10299EJ4V0DS00
PD16434
Figure 6-3. 16-Time-divisions
PD16434 Data memory address 14 13 12 11 10 9 8 7 6 5 0 1 1 Bank 0 1 1 1 1 0 0 1 1 Bank 1 0 1 1 0 0 1 0 0 1 0 0 0 0 1 0 0 1 0 0 1 0 1 0 0 1 0 0 0 0 1 0 0 1 0 0 1 0 1 0 0 1 0 0 0 0 1 0 0 1 0 0 1 0 0 1 1 1 1 1 1 0 0 1 1 0 1 1 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Timing strobe
4 1 0 0 0 0 1 1 0 1 1 1 0 0 1 0 0
3 1 0 0 0 1 0 1 0 1 0 1 0 0 0 1 0
2 1 0 0 1 0 0 1 0 1 0 1 0 0 0 1 0
1 1 0 1 0 0 0 1 0 1 0 1 0 0 0 1 0
0 1 1 0 0 0 0 1 0 1 0 0 1 1 1 0 0 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7
R0/R8 R1/R9 R2/R10 R3/R11 R4/R12 R5/R13 R6/R14 R7/R15
C14
C13
C12
C11
C10
C9
C8
C7
C6
C5
C4
C3
C2
C1
C0
To R0/R8 to R7/R15 of slave chip
Data Sheet S10299EJ4V0DS00
33
PD16434
Figure 6-4. 16-Time-divisions (When Displaying Characters A and 8)
1 frame
0 VDD VLC1 VLC2 VLC3 VLC4 VLC5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
ROW 0
ROW 1
VDD VLC1 VLC2 VLC3 VLC4 VLC5
ROW 15
VDD VLC1 VLC2 VLC3 VLC4 VLC5
VDD C10, C14 VLC2 VLC3 VLC5
VDD C11, C12, C13 VLC2 VLC3 VLC5
VLCD
1/5 VLCD ROW 1 to C14 -1/5 VLCD
-VLCD
34
Data Sheet S10299EJ4V0DS00
PD16434
7. STANDBY MODE
The PD16434 offers the standby mode in order to reduce the power consumption, when displaying operation is not necessary. The standby mode is set, by executing the STOP command. The standby mode is actually set, when the /BUSY signal is set to high after the STOP command is executed. In the standby mode, the PD16434 stops supplying the CLOCK signal to the LCD timing control circuit and the clock control circuit by internally masking the CLOCK signal. In addition, the PD16434 initializes the data processing mode to the auto-increment (I1I0 = 00) write mode. However, no other modes are affected by RESET operation, so that the interface mode and the display mode will be retained. The standby mode is cleared when a byte of data (command or data) is input, or when the RESET signal falls. However, the processing necessary during the standby mode and operation after clearing the standby mode differ, depending on which method is used. In addition, the CLOCK signal to the PD16434 can be stopped during the standby mode. In this case, the power consumption can be further reduced, compared to when the CLOCK is only internally masked.
7.1 Clearing Standby Mode
(1) Clearing standby mode by writing a byte of data If the previous operation modes (except the data processing mode), used before entering the standby mode, needs to be maintained, the standby mode can be cleared by writing a byte of data (command or data). In the serial interface mode, the standby mode is cleared, when writing 8 bits of serial data is completed (at the rising edge of the 8th /SCK). In the parallel interface, the standby mode is cleared, when writing the second 4-bit data is completed (at the rising edge of the 2nd /STB). When the chip address selection function is used in the serial interface mode, if /CS is set to high in the standby mode, the first 8-bit data, after /CS is set to low, is used as the chip address information, when the standby mode is cleared. Therefore, the standby mode is cleared, when writing the next 8-bit data is completed.
Remark During the standby mode, the clock necessary for driving the LCD by alternating current is stopped. Therefore, the LCD drive signal level, before entering the standby mode, is maintained in the standby mode. This means that a DC voltage remains applied to the LCD in the standby mode. To avoid this, control the VLC5 pin voltage using the CPU output port, as shown in Figure7-1, and output a high level from the output port, before executing the STOP command, to eliminate voltage differential between the VDD and VLC5.
Data Sheet S10299EJ4V0DS00
35
PD16434
Figure 7-1. Controlling LCD Drive Voltage
VDD VDD VDD (VLC0)
VLC1
VLC2
CPU
VLC3
PD16434
VLC4
VLC5
Output port
Remark The power fed to the CPU and the PD16434 must be from the same source.
(2) Clearing standby mode by RESET signal For a system for which only the contents of the data memory need be held when the standby mode is cleared, the RESET signal can be used to clear the standby mode. When using the RESET signal for clearing the standby mode, set the RESET signal to high after the standby mode is initiated (this can be checked by determining whether the /BUSY is set to high), then set the RESET signal to low when clearing the standby mode. While the RESET signal is high, the LCD drive voltage becomes the same as when it is in the reset operation, and no voltage is applied to the LCD. However, unlike normal reset operation, the contents of the data memory will not become undefined by the RESET signal. The data which existed before entering the standby mode is retained, and it can be used after clearing the standby mode. In a system which uses this method, the current path control by the RESET signal shown in Figure5-5 can be used.
7.2 Stopping Clock Supply and Retaining Data at Low Voltage in Standby Mode In the standby mode, only the data memory contents can be retained at a reduced voltage level. In this case, the power consumption can be further reduced by stopping the CLOCK supply to the PD16434. When stopping the CLOCK supply to the PD16434 in the standby mode, check that the PD16434 is in the standby mode (check that the /BUSY signal is high, after executing the STOP command), set the RESET signal to high, then stop the CLOCK supply to the PD16434 after the specified time period.
36
Data Sheet S10299EJ4V0DS00
PD16434
Figure 7-2. CLOCK Supply Stop Timing Waveforms in Standby Mode
STOP Standby mode
/BUSY
/CS
RESET
CLOCK tSRC Data can be retained at a reduced voltage tHRC
Data Sheet S10299EJ4V0DS00
37
PD16434
8. RESET OPERATION
The PD16434 is initialized as follows, when a high level is input to the RESET pin : * The chip address compare data (compared with CA1, CA0 inputs) is initialized to 00. In a multi-chip configuration, /BUSY output operation will differ, depending on whether CA1 and CA0 of the chip are 00 (coinciding address) or not (non-coinciding address) (refer to Figure 8-1). When CA1, CA0 = 00 : Sets /BUSY output to low, if /CS = 0. If /CS = 1, sets /BUSY output to high impedance. Other than 00 : Sets /BUSY output to high impedance, regardless of /CS input.
In a single chip configuration, /BUSY output operation is the same as that when CA1 and CA0 are 00.
* All processing operations (command/data processing, reading timing signal and display data to the row and column driver) are stopped.
* VLC3 level DC current is output from each LCD drive signal output pin (C0 to C41, R15/C42 to R8/C49, R0/R8 to R7/R15).
* The internal functions are set as follows (to the same conditions as when these commands are executed) : SWM (I1I0 = 00) : Auto-increment mode
LDPI (D6 to D0 = 0000000) : Data pointer is cleared to 0 SMM (M2 to M0 = 000) : 8-time-divisions, R0/R8 to R7/R15 pins serve as R0 to R7 pins, SYNC pin is set in the input mode, the data memory is set to bank 0. SFF (F2 to F0 = 000) : Frame frequency is set to fCL/2 .
14
* The byte transfer end counter is cleared. * If the PD16434 is in the standby mode, the standby mode is maintained. * The data memory contents become undefined.
When the high level input to the RESET pin is returned to low, the operation becomes possible, according to the initialized contents. In addition, the next processing will be performed at the falling edge of the RESET signal. The display output will be the same as when the DISP OFF is executed.
* The interface specification code (serial/parallel specification, chip address selection function provided/ unprovided) is read from the D2(CAE) and D1(P, /S) pins.
* A chip, whose CA1 and CA0 values are 0, becomes selected state.
38
Data Sheet S10299EJ4V0DS00
PD16434
* If a RESET is executed during the standby mode, the standby mode is cleared. In this case, the data memory contents are retained.
Figure 8-1. Example of /BUSY Output Timing Waveforms by RESET Input
(a) when CA1, CA0 00
RESET
/CS /BUSY Hi-Z
Output from selected chip
Output from no chip
Output from chip whose CA1 and CA0 values are 00
(b) when CA1, CA0 = 00 and /CS = 0
RESET
/CS /BUSY
"L"
Output from selected chip
Output from chip, whose CA1 and CA0 values are 00
Data Sheet S10299EJ4V0DS00
39
PD16434
9. COMMANDS
The PD16434 offers the following 16 different commands, each consisting of 1 byte (8 bits) :
Table 9-1. List of Commands Mnemonic SFF SMM DISP OFF DISP ON LDPI SRM SWM SORM SANDM SCML SCMR BRESET BSET CLCURS WRCURS STOP Operation Set Frame Frequency Set Multiplexing Mode Display Off Display On Load Data Pointer with Immediate Set Read Mode Set Write Mode Set OR Mode Set AND Mode Set Character Mode with Left entry Set Character Mode with Right entry Bit Reset Bit set Clear Cursor Write Cursor Set Stop Mode Hexadecimal code 10 to 14 18 to 1F 08 09 80 to B1, C0 to F1 60 to 63 64 to 67 68 to 6B 6C to 6F 71 72 20 to 3F 40 to 5F 7C 7D 01
9.1 LCD Display Mode Setting Commands The following commands are provided for LCD display mode setting :
SFF (Set Frame Frequency) SMM (Set Multiplexing Mode) DISP OFF (Display Off) DISP ON (Display On) (1) SFF (Set Frame Frequency)
0
0
0
1
0
F2
F1
F0
This command sets the frame frequency. The frame frequency will be the clock frequency input from the CLOCK pin divided by the frequency dividing ratio specified by F2 to F0.
40
Data Sheet S10299EJ4V0DS00
PD16434
F2 0 0 0 0 1 1
F1 0 0 1 1 0 0 to
F0 0 1 0 1 0 1
Frame Frequency fCL/2 fCL/2 fCL/2 fCL/2 fCL/2
14
13
12
11
10
These settings are not allowed.
1
1
1
Remark fCL : Clock frequency
(2) SMM (Set Multiplexing Mode)
0
0
0
1
1
M2
M1
M0
This command specifies the number of time divisions, and the functions of the row driver, and the row/column driver, input/output for the SYNC pin, and the data memory bank. Number of time divisions R0/R8 to R7/R15 R15/C42 to R8/C49 SYNC pin Memory bank 0 Input 0 0 0 1 1 1 1 0 1 1 0 0 1 1 1 8 0 Output 1 0 R8 to R15 1 16 0 R0 to R7 1 R15 to R8 Output 0, 1 Input C42 to C49 1 R0 to R7 0 1
M2
M1
M0
0
0
0
Data Sheet S10299EJ4V0DS00
41
PD16434
(3) DISP OFF (Display Off)
0
0
0
0
1
0
0
0
This command sets the relationship of the row signal and column signal to non-select level, regardless of the display data, and deletes display.
(4) DISP ON (Display On)
0
0
0
0
1
0
0
1
When this command is executed, the display operation will be performed according to the display data. 9.2 Data Pointer Load Command
(1) LDPI (Load Data Pointer with Immediate)
1
D6
D5
D4
D3
D2
D1
D0
Remark D6 to D0 = 00H to 31H, 40H to 71H
This command loads 7-bit immediate data D6 to D0 to the data pointer. 9.3 Data Processing Mode Setting Commands The following six different commands are available as the data processing mode setting commands.
SRM (Set Read Mode) SWM (Set Write Mode) SORM (Set OR Mode) SANDM (Set AND Mode) SCML (Set Character Mode with Left Entry) SCMR (Set Character Mode with Right Entry)
Each of these commands sets the PD16434 to the respective mode. Afterwards, the PD16434 processes data in the specified mode until a command to set a different processing mode is executed. The lower 2 bits (I1I0) of these data processing mode setting commands specify the data pointer modification operation for each byte data processing. The data pointer is modified as follows:
42
Data Sheet S10299EJ4V0DS00
PD16434
I1 0 0 1 1 I0 0 1 0 1 Data pointer contents of modification Automatically incremented (+1) each time a byte of data is processed. Automatically decremented (-1) each time a byte of data is processed. This setting is not allowed. No modification (the same address is maintained)
(1) SRM (Set Read Mode)
0
1
1
0
0
0
I1
I0
The data processing mode is set to the read mode by this command. Afterwards, data processing will be performed in the read mode. When this mode is set, the contents of the data memory, addressed by the current contents of the data pointer, are automatically transferred to the serial/parallel register. The data pointer is then modified according to I1I0. When all 8 bits of the serial/parallel register contents are read by the CPU, the contents of the data memory, addressed by the modified data pointer, are automatically transferred into the serial/parallel register for the next read operation. Afterwards, the same operation is repeated by the CPU, each time an 8-bit data is read.
(2) SWM (Set Write Mode)
0
1
1
0
0
1
I1
I0
The data processing mode is set to the write mode by this command. Afterwards, data processing will be performed in the write mode. When this mode is set, the 8-bit data written into the serial/parallel register by the CPU is stored into the data memory addressed by the current contents of the data pointer. The data pointer is then modified, according to I1I0. Afterwards, the same operation is repeated, each time an 8-bit data is written by the CPU.
(3) SORM (Set OR Mode)
0
1
1
0
1
0
I1
I0
The data processing mode is set to the OR mode by this command. Afterwards, data processing will be performed in the OR mode. When this mode is set, the 8-bit data, written into the serial/parallel register by the CPU, is ORed with the data
Data Sheet S10299EJ4V0DS00
43
PD16434
memory addressed by the current contents of the data pointer, and the result will be stored into the same data memory address. The data pointer is then modified, according to I1I0. Afterwards, the same operation is repeated, each time an 8-bit data is written by the CPU.
(4) SANDM (Set AND Mode)
0
1
1
0
1
1
I1
I0
The data processing mode is set to the AND mode by this command. Afterwards, data processing will be performed in the AND mode. When this mode is set, the 8-bit data, written into the serial/parallel register by the CPU, is ANDed with the data memory addressed by the current contents of the data pointer, and the result will be stored into the same data memory address. The data pointer is then modified, according to I1I0. Afterwards, the same operation is repeated, each time an 8-bit data is written by the CPU.
(5) SCML (Set Character Mode with Left entry)
0
1
1
1
0
0
0
1
The data processing mode is set to the character mode with left entry by this command. Afterwards, data processing will be performed in the Character mode with left entry. When this mode is set, the 8-bit data written into the serial/parallel register by the CPU is treated as ASCII or JIS code and is decoded to 5 x 7-bit character display data by the character generator. It is written into the lower five consecutive data memory addresses from the address indicated by the current contents of the data memory. As a result, the data pointer contents are subtracted by 5 (-5). Afterwards, the same operation is repeated, each time an 8-bit data is written by the CPU.
(6) SCMR (Set Character Mode with Right entry)
0
1
1
1
0
0
1
0
The data processing mode is set to the character mode with right entry by this command. Afterwards, data processing will be performed in the character mode with right entry. When this mode is set, the 8-bit data written into the serial/parallel register by the CPU is treated as ASCII or JIS code and is decoded to 5 x 7-bit character display data by the character generator, and is written into the subsequent five data memory addresses from the address indicated by the current contents of the data memory. As a result, the data pointer contents are added by 5 (+5). Afterwards, the same operation is repeated, each time an 8-bit data is written by the CPU.
44
Data Sheet S10299EJ4V0DS00
PD16434
9.4 Memory Bit Manipulation Commands The following four different memory bit manipulation commands are available:
BRESET (Bit Reset) BSET (Bit Set) CLCURS (Clear Cursor) WRCURS (Write Cursor)
The BRESET and BSET commands can be executed in any data processing mode. After the bit specified by the BRESET/BSET command in the data memory addressed by the data pointer is set/reset, the data pointer is modified according to the lower 2 bits (J1J0) of the command byte. The CLCURS or WRCURS command is used to clear or set the cursor (bit 7 position) in the character mode. After these commands are executed, the data pointer contents are added by 5 or subtracted by 5. Data pointer manipulation by these memory bit manipulation commands is effective, only when these commands are executed. Afterwards, the data pointer is modified according to the data processing mode that has been set. However, the data pointer contents are modified by the memory bit manipulation command. Therefore, the modified value will be used as the initial value for the subsequent modification operation. The figure below shows the BRESET and BSET command bit specifications and modification contents for the data pointer.
7 B2 B1 B0 000 001 0 Data memory
to
111
J1 0 0 1 1
J0 0 1 0 1 +1 -1
Data pointer contents for modification
This setting is not allowed No modification (The same address is maintained)
Data Sheet S10299EJ4V0DS00
45
PD16434
(1) BRESET (Bit Reset)
0
0
1
B2
B1
B0
J1
J0
This command or these commands resets (to 0) the bit specified by B2 to B0 of the data memory addressed by the data pointer. Afterwards, the data pointer is modified according to J1J0.
(2) BSET (Bit Set)
0
1
0
B2
B1
B0
J1
J0
This command or these commands sets (to 1) the bit specified by B2 to B0 of the data memory addressed by the data pointer. Afterwards, the data pointer is modified according to J1J0.
(3) CLCURS (Clear Cursor)
0
1
1
1
1
1
0
0
When this command is executed in the character mode, bit 7 of each data memory of the five subsequent addresses (SCMR mode) or the lower five consecutive addresses (SCML mode) from the address, indicated by the current contents of the data pointer, is reset (to 0). This command can be used to clear the cursor displayed for 5 x 7-bit configuration character.
(4) WRCURS (Write Cursor)
0
1
1
1
1
1
0
1
When this command is executed in the character mode, bit 7 of each data memory of the five subsequent addresses (SCMR mode) or the lower five consecutive addresses (SCML mode) from the address, indicated by the current contents of the data pointer, is set (to 1). This command can be used to display the cursor for 5 x 7-bit configuration character.
46
Data Sheet S10299EJ4V0DS00
PD16434
9.5 Standby Operation Setting Command
(1) STOP (Set Stop Mode)
0
0
0
0
0
0
0
1
This command sets the STOP mode (standby mode). The data processing mode is initialized to the auto-increment (I1I0 = 00) write mode. Other modes are not affected by this command execution.
Data Sheet S10299EJ4V0DS00
47
PD16434
10. SYSTEM CONFIGURATION EXAMPLE
Shows a circuit example, when four PD16434s are used in a multi-chip system configuration.
Figure 10-1. System Configuration Example (Multi-Chip)
LCD (40 characters x 2 lines)
D0 to D3
CLOCK /CS RESET C, /D /BUSY /STB SYNC
R0 to R7 C49 to C0 CA1 (0) CA0
C49 to C0 (1) CA1 CA0
C49 to C0 (2) CA1 CA0
C49 to C0 R8 to R15 CA1 (3) CA0
PD16434 x 4
CPU
48
Data Sheet S10299EJ4V0DS00
D0 to D3 CLOCK /CS RESET C, /D /BUSY /STB
PD16434
11. ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings (TA = 25 C)
Parameter Power Supply Voltage LCD Drive Voltage Input Voltage Output Voltage Operating Ambient Temperature Storage Temperature
Note
Symbol VDD VLCD VI VO TA Tstg
Conditions
Ratings -0.3 to +7.0
Unit V V V V C C
VDD = 5.0 V
0 to 12.5 -0.3 to VDD + 0.3 -0.3 to VDD + 0.3 -40 to +85 -65 to +150
Note VLCD = VDD - VLC5 Caution If the absolute maximum rating of even one of the above parameters is exceeded even momentarily, the quality of the product may be degraded. Absolute maximum ratings, therefore, specify the values exceeding which the product may be physically damaged. Be sure to use the product within the range of the absolute maximum ratings. Recommended Operating Range
Parameter Power Supply Voltage LCD Drive Voltage (VDD = 4.5 to 5.5V) LCD Drive Voltage (VDD = 2.7 to 4.5V) Logic Input Voltage Drive Input Voltage Symbol VDD VLCD VLCD VIN VLC1 to VLC4 Conditions MIN. 2.7 4.5 2.5 0 VLC5 TYP. MAX. 5.5 12.0 10.5 VDD VDD Unit V V V V V
Data Sheet S10299EJ4V0DS00
49
PD16434
DC Characteristics 1 (TA = -40 to + 85 C, VDD = 5 V 10 %, VLC5 = -6.0 V 10 %)
Parameter High Level Input Voltage Symbol VIH1 VIH2 Low Level Input Voltage High Level Input Leakage Current Low Level Input Leakage Current High Level Output Voltage VIL ILIH ILIL VOH1 VI = VDD VI = 0 V /BUSY, D0 to D3, IOH = -400 A VOH2 Low Level Output Voltage VOL1 VOL2 High Level Output Leakage Current Low Level Output Leakage Current Row Output Impedance Row/Column Output Impedance ILOL RROW RROW /COL Column Output Impedance Supply Current RCOL IDD1 IDD2 Operation mode, fC = 400 kHz STOP mode, CLK = 0 V 15 250 30 600 25 k VO = 0 V 6 7.5 -10 16 20 ILOH SYNC, IOH = -100 A /BUSY, D0 to D3, IOL = 1.7 mA SYNC, IOL = 100 A VO = VDD VDD - 0.5 0.5 0.5 10 V V V VDD - 0.5 Conditions Except for /SCK /SCK MIN. 0.7 VDD 0.8 VDD 0 TYP. MAX. VDD VDD 0.3 VDD 10 -10 Unit V V V
A A
V
A A
k k
A A
Capacitance (TA = 25 C, VDD = 0 V)
Parameter Input Capacitance Output Capacitance I/O Capacitance Symbol CIN COUT CIO f = 1 MHz Unmeasured pins returned to 0 V. Conditions MIN. TYP. MAX. 10 25 15 Unit pF pF pF
50
Data Sheet S10299EJ4V0DS00
PD16434
AC Characteristics 1 (TA = - 40 C to + 85 C, VDD = + 5 V 10 %) Common Operation
Parameter Clock Operation Frequency Clock High Level pulse Width Clock Low Level pulse Width RESET High Level Width /CS /BUSY Delay Time /CS /BUSY Float Delay Time /CS High Level Width SYNC Load Capacitance Data Set Time (RESET) Data Hold Time (RESET) Symbol fC tWHC tWLC tHRS tDCSB tDCSBF tWHCS CLSY tSDR tHRD 0 5 CL = 50 pF CL = 50 pF 4 100 Conditions MIN. 100 350 350 4 3 5 TYP. MAX. 1100 Unit kHz ns ns
s s s s
pF
s s
Serial Input / Output Operation
Parameter /SCK Period /SCK High Level Pulse Width /SCK Low Level Pulse Width High Level /SCK Hold Time (/BUSY) SI Set Time (/SCK) SI Hold Time (/SCK) /SCK SO Delay Time 8th /SCK /BUSY Delay Time /BUSY Low Level Time C,/D Set Time (1st /SCK) C,/D Hold Time (8th /SCK) /CS Hold Time (8th /SCK) Symbol tCYK tWHK tWLK tHBK tSIK tHKI tDKO tDKB tWLB tSDK tHKD tHKCS CL = 50 pF CL = 50 pF CL = 50 pF 18 0 3 5 Conditions MIN. 0.9 400 400 0 120 270 350 4 64 TYP. MAX. Unit
s
ns ns ns ns ns ns
s
1/fC
s s s
Data Sheet S10299EJ4V0DS00
51
PD16434
Parallel Input / Output Operation
Parameter Command Input Set Time (/STB) Command Input Hold Time (/STB) Data Input Set Time (/STB) Data Input Hold Time (/STB) Data Output Delay Time Data Output Hold Time /STB Low Level Pulse Width /STB High Level Time /STB Hold Time (/BUSY) 2nd /STB /BUSY Delay Time /BUSY Low Level Time C,/D Set Time (1st /STB) C,/D Hold Time (2nd /STB) /CS Hold Time (2nd /STB) Symbol tA tB tC tD tACC tH tSL tSH tHBS tDSB tWLB tSDS tHSD tHSCS CL = 50 pF 18 0 3 3 Conditions CL = 80 pF CL = 20 pF CL = 80 pF CL = 20 pF CL = 80 pF CL = 20 pF 0 700 1 0 4 64 MIN. 120 110 250 70 750 150 TYP. MAX. Unit ns ns ns ns ns ns ns
s s s
1/fC
s s s
52
Data Sheet S10299EJ4V0DS00
PD16434
DC Characteristics 2 (Unless otherwise specified, TA = -40 to + 85 C, VDD = 3 V 10 %, VDD - VLC5 = 9 V 10 %)
Parameter High Level Input Voltage Symbol VIH1 VIH2 Low Level Input Voltage High Level Input Leakage Current Low Level Input Leakage Current High Level Output Voltage VIL ILIH ILIL VOH1 VOH2 Low Level Output Voltage VOL1 VOL2 High Level Output Leakage Current Low Level Output Leakage Current Row Output Impedance Row/Column Output Impedance Column Output Impedance Supply Current ILOH ILOL RROW RROW/COL RCOL IDD1 IDD2 Operation mode, fC = 400 kHz STOP mode, CLK = 0 V VI = VDD VI = 0 V /BUSY, D0 to D3, IOH = -100 A SYNC, IOH = -100 A /BUSY, D0 to D3, IOL = 500 A SYNC, IOL = 100 A VO = VDD VO = 0 V 8 10 20 150 250 20 VDD - 0.5 VDD - 0.5 0.5 0.5 10 -10 Conditions Except for /SCK /SCK MIN. 0.7 VDD 0.8 VDD 0 TYP. MAX. VDD VDD 0.3 VDD 10 -10 Unit V V V
A A
V V V V
A A
k k k
A A
Capacitance (TA = 25 C, VDD = 0 V)
Parameter Input Capacitance Output Capacitance I/O Capacitance Symbol CIN COUT CIO f = 1 MHz With pins other than that measured at 0 V. Conditions MIN. TYP. MAX. 10 25 15 Unit pF pF pF
Data Sheet S10299EJ4V0DS00
53
PD16434
AC Characteristics 2 (Unless Otherwise Specified, TA = - 40 C to + 85 C, VDD = + 3 V 10 %) Common Operation
Parameter Clock Operation Frequency Clock High Level pulse Width Clock Low Level pulse Width RESET High Level Width /CS /BUSY Delay Time /CS /BUSY Float Delay Time /CS High Level Width SYNC Load Capacitance Data Set Time (RESET) Data Hold Time (RESET) Symbol fC tWHC tWLC tHRS tDCSB tDCSFB tWHCS CLSY tSDR tHRD 0 10 CL = 50 pF CL = 50 pF 10 100 Conditions MIN. 20 350 350 4 4 6 TYP. MAX. 800 Unit kHz ns ns
s s s s
pF
s s
Serial Input / Output Operation
Parameter /SCK Period /SCK High Level Pulse Width /SCK Low Level Pulse Width High Level /SCK Hold Time (/BUSY) SI Set Time (/SCK) SI Hold Time (/SCK) /SCK SO Delay Time 8th /SCK /BUSY Delay Time /BUSY Low Level Time C, /D Set Time (1st /SCK) C, /D Hold Time (8th /SCK) /CS Hold Time (8th /SCK) Symbol tCYK tWHK tWLK tHBK tSIK tHKI tDKO tDKB tWLB tSDK tHKD tHKCS CL = 50 pF CL = 50 pF CL = 50 pF 18 0 4 6 Conditions MIN. 1 450 450 0 200 500 400 5 64 TYP. MAX. Unit
s
ns ns ns ns ns ns
s
1/fC
s s s
54
Data Sheet S10299EJ4V0DS00
PD16434
Parallel Input / Output Operation
Parameter Command Input Set Time (/STB) Command Input Hold Time (/STB) Data Input Set Time (/STB) Data Input Hold Time (/STB) Data Output Delay Time Data Output Hold Time /STB Low Level Pulse Width /STB High Level Time /STB Hold Time (/BUSY) 2nd /STB /BUSY Delay Time /BUSY Low Level Time C, /D Set Time (1st /STB) C, /D Hold Time (2nd /STB) /CS Hold Time (2nd /STB) Symbol tA tB tC tD tACC tH tSL tSH tHBS tDSB tWLB tSDS tHSD tHSCS CL = 50 pF 18 0 4 4 Conditions CL = 80 pF CL = 20 pF CL = 80 pF CL = 20 pF CL = 80 pF CL = 20 pF 0 2000 3 0 5 64 MIN. 200 180 450 100 2000 900 TYP. MAX. Unit ns ns ns ns ns ns ns
s s s
1/fC
s s s
Data Sheet S10299EJ4V0DS00
55
PD16434
AC timing measurement voltages (except /STB,/SCK, /BUSY)
0.7 VDD Test points 0.3 VDD 0.3 VDD 0.7 VDD
Clock timing waveforms
1/fc
tWHC
CL
tWLC
RESET input timing waveforms
tHRS
RESET
Interface specification timing waveforms
RESET
tSDR
tHRD
D1,D2
56
Data Sheet S10299EJ4V0DS00
PD16434
Serial input / output timing waveforms
tWHCS
/CS
tDCSB
tHKCS
C, /D
Command/data specification
tSDK
tHKD
tDCSBF
/BUSY
VDD-0.5 V 0.45 V tCYK tHBK tWHK tDKB tWLB
/SCK 1st 2nd tWLK tSIK 8th
tHKI Serial data (LSB)
SI
Serial data (MSB)
tDKO
SO
Data Sheet S10299EJ4V0DS00
57
PD16434
Parallel input / output timing waveforms
tWHCS
/CS
tDCSB
tHSCS
C, /D
tSDS
tHSD
tDCSBF
/BUSY
tHBS
tSH
tDSB
tWLB
/STB
1st tB tC
2nd tSL
tA
tD
D0 to D3
Control input
Data input
tACC
tH
D0 to D3
Data output
58
Data Sheet S10299EJ4V0DS00
PD16434
Data Memory STOP Mode Low Power Supply Voltage Data Retention Characteristics (TA = -40 to +85 C)
Parameter Data Retention Power Supply Voltage Data Retention Power Supply Current Data Retention High Level RESET Input Voltage RESET, CLOCK Setup Time RESET, CLOCK Hold Time tSRC tHRC 10 10 VIHDR 0.9 VDDDR VDDDR + 0.2 V IDDDR VDDDR = 2.0 V 20 Symbol VDDDR Conditions MIN. 2.0 TYP. MAX. Unit V
A
s s
Data retention timing waveforms
Data retention mode
VDD
1
2 RESET 4
3
2 4
CLOCK
tSRC
tHRC
1 2 3 4
VDDDR VIH1 VIHDR VIL
Remark All inputs must be set below VDDDR in the data retention mode.
Data Sheet S10299EJ4V0DS00
59
PD16434
12. PACKAGE DRAWINGS
PD16434G-xxx-12
80-PIN PLASTIC QFP (14x20)
A B
64 65
41 40
detail of lead end S CD Q R
80 1
25 24
F G H I
M
J
P
K S N S L M
NOTE Each lead centerline is located within 0.15 mm of its true position (T.P.) at maximum material condition.
ITEM A B C D F G H I J K L M N P Q R S
MILLIMETERS 24.70.4 20.00.2 14.00.2 18.70.4 1.0 0.8 0.370.08 0.15 0.8 (T.P.) 2.350.2 1.20.2 0.17 +0.08 -0.07 0.15 2.05 +0.2 -0.1 0.10.1 3+7 -3 2.45 MAX. P80G-80-12-3
60
Data Sheet S10299EJ4V0DS00
PD16434
5
PD16434GF-xxx-3B9
5
80-PIN PLASTIC QFP (14x20)
A B
64 65
41 40
detail of lead end S CD Q R
80 1
25 24
F G H I
M
J
P
K M N S L S
NOTE Each lead centerline is located within 0.15 mm of its true position (T.P.) at maximum material condition.
ITEM A B C D F G H I J K L M N P Q R S
MILLIMETERS 23.20.2 20.00.2 14.00.2 17.20.2 1.0 0.8 0.37 +0.08 -0.07 0.15 0.8 (T.P.) 1.60.2 0.80.2 0.17 +0.08 -0.07 0.10 2.70.1 0.1250.075 55 3.0 MAX. S80GF-80-3B9-5
Data Sheet S10299EJ4V0DS00
61
PD16434
13. RECOMMENDED SOLDERING CONDITIONS
When mounting the PD16434 by soldering should be performed under the following recommended conditions. Should other than recommended conditions be used, consult with our sales personnel. Surface Mount Type
PD16434G-xxx-12
5
Soldering Method
: 80-PIN PLASTIC QFP (14 x 20)
Soldering Condition Symbol of Recommended Soldering Condition
PD16434GF-xxx-3B9: 80-PIN PLASTIC QFP (14 x 20)
Infrared reflow
Package peak temperature : 235 C, Time : 30 seconds MAX. (210 MIN.), Number of times : 2 MAX.
IR35-00-2
VPS
Package peak temperature : 235 C, Time : 40 seconds MAX. (200 MIN.), Number of times : 2 MAX.
VP-15-00-2
Wave soldering
Solder path temperature : 260 C MAX., Time : 10 seconds MAX., Number of times : 1, Preheating temperature : 120 C MAX. (Package sutface)
WS-60-00-1
5
Partial heating
Pin temperature: 300 C MAX., Time: 3 seconds MAX. (per side of device)
-
Caution Do not use two or more soldering methods in combination (except the partial heating method).
62
Data Sheet S10299EJ4V0DS00
PD16434
NOTES FOR CMOS DEVICES
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.
Data Sheet S10299EJ4V0DS00
63
PD16434
Reference Documents NEC Semiconductor Device Reliability/Quality Control System (C10983E) Semiconductor Device Mounting Technology Manual (C10535E)
* The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. * NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. * Descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. * While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. * NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance.
M7 98. 8

▲Up To Search▲

Price & Availability of UPD16434

	To Download UPD16434 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .